Back Home

MX5 ROLL BARS

 

GPVWHB ROLLBAR 3 IN STOCK AND READY FOR DESPATCH


GPVWHB
MAZDA MX5 WITH WELDED HARNESS BAR
Price: £250.00

*******************************************************

GPDWHB
MAZDA MX5 WITH WELDED HARNESS BAR
Price: £250.00


2 IN STOCK AND READY FOR DESPATCH



**********************************************************

TT ROLL BAR
MAZDA MX5 TT ROLL BAR
Price: £350.00

OUT OF STOCK


**********************************************************

GPV
MAZDA MX5 GPV ROLL BAR
Price: £250.00








**

1 IN STOCK AND READY FORDESPATCH


********************************************************


GPD
MAZDA MX5 GPD ROLL BAR
Price: £250.00










OUT OF STOCK

***********************************************************


GP
MAZDA MX5 GP ROLL BAR
Price: £240.00









1 IN STOCK AND READY FOR DESPATCH

*********************************************************


GPXWHB ROLL BAR
.
Price: £320.00

OUT OF STOCK 

===============================================

Fits all right and left hand drive Mk1, Mk2 & 2.5 models, 1989>2005

Please note: This is not suitable for use with any other style bar or wind blocker except the Mk2/2.5 factory wind blocker (minor modifications will be required).

Disclaimer:  TR Lane NOT will be responsible or held liable for any damage, loss or injury sustained whilst fitting or using this product. 



GP ROLL BAR FITTING INSTRUCTIONS

 

1.  MOVE BOTH SEATS FORWARD, TILTED FORWARD, GIVING ACCESS

     TO REAR AREA.   POSITION HOOD IN DOWN POSITION.  REMOVE

     SEAT BELT SHOULDER STRAPS FROM TOP OF SEAT BELT TOWERS.

     REMOVE PLASTIC COWLING SURROUNDING SEAT BELT TOWERS,

     GIVING ACCESS TO SEAT BELT REELS.  REMOVE YOUR PARCEL

     SHELF CARPET AND FIRE WALL CARPET.  REMOVE PARCEL SHELF

     TRAY, TAKING GREAT CARE AS THIS ITEM CAN BE VERY SHARP.

     THIS WILL GIVE YOU ACCESS TO WHERE THE ROLL BAR NEEDS TO

     SIT. 

 

2.  JACK UP CAR,  SECURELY UPON AXLE STANDS.  REMOVE REAR

     WHEELS.  REMOVE SPLASH TRAYS WHICH ARE LOCATED IN FRONT

     OF THE REAR WHEELS, IN FRONT OF THE ARCHES.  WHERE ROLL BAR

     SITS IN CAR, YOU WILL NEED TO LOOSEN ALL FIXINGS WHICH

     HOLD WIRING HARNESSES IN POSITION.  THERE ARE ALSO THREE

     SMALL BOLTS ON EACH SIDE OF THE SEAT BELT TOWERS BY YOUR

     WIRING HARNESSES - THESE NEED TO BE REMOVED.   THE TWO

     ANGLE BRACKETS WHICH THE REAR PARCEL SHELF MOUNTS TO,

     YOU WILL NEED TO REMOVE 4" OF THIS EACH SIDE, ENABLING YOUR

     ROLL BAR TO SIT NEATLY BETWEEN SEAT BELT TOWERS.

 

3.  PROCEED TO FIT ROLL BAR IN POSITION, USING YOUR SEAT BELT

     TOWER BOLTS, LOCATE THE ROLL BAR SIDE MOUNTING PLATES,

     YOU MAY NEED TO MAKE SOME SPACERS OR YOU CAN USE

     EXISTING TOP HAT SPACERS THAT HAVE COME OFF YOUR 

     SHOULDER STRAP BOLTS.  PROCEED TO LIGHTLY TIGHTEN THESE

     BOLTS, ENSURING THAT THE ROLL BAR FEET PLATES ARE SITTING

     ON THE CHASSIS AREA.  ADJUST YOUR ROLL BAR SO THAT THE

     FEET PLATES SPREAD OUT NEATLY BETWEEN THE SEAT BELT

     TOWER SIDES (THERE MAY BE A GAP IF A HARNESS BAR IS 

     PROVIDED DUE TO WELDING HEAT DISTORTION) BUT THIS CAN

     BE OVERCOME BY BOLTING TO THE SIDES OF PILLARS. 

 

4.  WITH A CENTRE PUNCH, PUNCH DOWN THROUGH THE HOLES AS

     HARD AS YOU CAN, THEN YOU WILL FEEL UNDER THE CAR WHERE

     YOU HAVE PUNCHED DOWN THROUGH, PUNCH BACK UP THROUGH

     FROM UNDERNEATH, THEN WITH A PILOT DRILL, DRILL UP THROUGH

     AND THEN DRILL AGAIN WITH APPROPRIATE DRILL.  BOLTS DOWN

     THROUGH, THERE ARE BACKING PLATES TO BE ATTACHED ON

     REAR STAYS WHICH CAN NOW BE TIGHTENED IN POSITION. 

 

5.  REMOVE SEAT BELT REELS, YOU MAY PROCEED TO DRILL THROUGH

     THE SIDE MOUNTING PLATES AND THEN PROCEED TO NUT AND

     BOLT TOGETHER, AND THEN RE-ATTACH SEAT BELT REELS. 

     (AS A SAFETY MEASURE, GET A SECOND PERSON TO CHECK THAT

     YOU HAVE TIGHTENED THE SEAT BELT REELS).  FINALLY CHECK

     THAT YOU HAVE TIGHTENED ALL THE NUTS AND BOLTS.  WHEN

     YOU ARE HAPPY WITH INSTALLATION, YOU MAY PROCEED TO

     REPLACE SPLASH TRAYS, FIX WHEELS, SET BACK DOWN ON THE

     FLOOR. 

 

6.  YOU WILL NOW NEED TO TRIM YOUR REAR PARCEL SHELF AREA.

     THIS IS UP TO THE INDIVIDUAL HOW THEY WISH TO DO THIS. 

     ONCE YOU HAVE FITTED THE PARCEL SHELF, YOU WILL THEN

     NEED TO TRIM THE BOTTOM EDGES OF THE SEAT BELT COWLINGS,

     ENABLING THEM TO SLIP FROM THE COCKPIT AREA BACK TOWARDS

     THE BACK OF THE CAR, SLIDING BETWEEN THE ROLL BAR AND

     SEAT BELT TOWERS.  THIS CAN SOMETIMES BE A TIGHT FIT AND

     MAY NEED SOME GENTLE PERSUASION AND EASING.  THEN

     PROCEED TO FIT PARCEL SHELF CARPET AND TRIM AS DESIRED. 

    

 

T.R. Lane Fabrications or any employee of T.R. Lane Fabrications are not in anyway responsible or liable for loss or injury to any persons whilst fitting or using this roll bar.

This is part of the sale agreement.